¥9860
起订量
≥1件
总供应
20件
所在地
河北省沧州市
河北远东泵业 供应W2.1zk24Z1M1W73 双螺杆泵 油脂输送泵 泵体采用铸铁材质
●泵体内装有两根左、有施单头螺纹的螺杆,主动螺杆2由动力机驱动转动时,靠同步齿轮1带动从动螺杆3转动。两根螺杆以及螺杆与泵体.之间存在着间隙,该间隙靠齿轮和轴承保证。其间隙大小,取决于液体粘度、工作压力等因素。由于每根螺杆两端螺纹的旋向相反,螺杆转动时,由螺杆啮合线形成的泵工作腔。
●该型泵采用双吸式结构,螺杆两端处于同一压力腔中,轴向力可以自行平衡。两端轴承采用外装式,单独采用润滑油(脂)润滑,因而不受输送介质的影响。两螺杆间用一对同步齿轮驱动,螺杆齿面间并不接触,而留有一微小间隙,介质中的杂质并不能对螺杆齿面产生直接的磨损(除冲刷外)。 除一些小排量泵外(2W.W4.0以下),一般在泵体上都带有内流式安全阀,当排放压力超过额定值时,有一定的保护作用。 泵体上的进出口方向有两种,一为水平进,水平出;二为水平进,垂直向上出;用户可根据自己需要选择。This type pump adopts double suction type structure, at the e pressure in the cavity on both ends of the screw, the axial force can balance itself.Both ends of bearing mounted outside using, lubricated by lubricating oil (grease) separately, and therefore not affected by the medium.With a pair of synchronous gears drive between the two screw, the screw does not contact between tooth surfaces, and leave a small gap, the impurities in medium can not be directly on the screw tooth surface wear (except wash).Except a few small displacement pump (below 2 w. W4.0), generally contain flow relief valve on the pump body, when the discharge pressure exceeds rating, has certain protective effect.There are two kinds of the direction of the import and export on the pump body, one for level, level;Secondly, level, vertical;User can choose according to their own needs.
1.流量Q:
作为容积式泵,影响双螺杆泵流量的因素主要有转速n,压力p,以及介质的粘度v。The selection of performance parameters:
1. The flow Q:
As a positive displacement pump, double screw pump flow effects are the major factors of rotational speed n, pressure p, and the medium viscosity v.
1.1转速n的影响:
螺杆泵(高温双螺杆泵,大流量双螺杆泵)在工作时,两螺杆及衬套之间形成密封腔,螺杆每转动一周便由进口向出口移出一个密封腔,即一个密封腔的体积的液体被排出去。理想状态下,泵内部无泄漏,那么泵的流量与转速成正比。即:Qth=n*q n----转速; q----理论排量,即泵每转一周所排出的液体体积; Qth----理论排量。The influence of the rotational speed n 1.1:Screw pump (high temperature double screw pump, large flow of double screw pump) at work, the sealed cavity formed between the two screw and bushing, the screw rotation per week will remove a sealed cavity from import to export, that is, a sealed cavity volume of liquid is out.Internal leak-off ideally, pump, the pump flow rate is proportional to the speed.Namely: Qth q = n * n - speed;Q - the theory of displacement, the pump discharge by turn every week liquid volume;Qth - the theory of displacement.
1.2压力 △P的影响:
双螺杆泵(高温双螺杆泵,大流量双螺杆泵)实际工作过程中,其内部存在泄漏,也称滑移量。由于泵的密封腔有一定的间隙,且密封腔前、后存在压差 △P,因此,有一部分液体回流,即存在泄漏,泄漏量用 △Q表示,则Q=Qth-△Q.显而易见,随着密封腔前、后压差 △P升高,泄漏量 △Q逐渐增大。对于不同型线和结构,影响大小也各不相同。The influence of pressure delta P 1.2:
Double screw pump (high temperature double screw pump, large flow of double screw pump) in the process of the actual work, its internal is leaking, also known as slippage.Due to pump seal chamber has a certain gap, and seal chamber before and after the differential delta P, as a result, some liquid reflux, is leakage, leakage in delta Q, Q = Qth - delta Q. Obviously, as the seal chamber pressure difference before and after the delta P increases, leakage delta Q increases gradually.For different lines and structure, effect size are different.
1.3粘度v的影响:试想:将清水和粘稠的浆糊以相同的体积从漏斗式的容器中泄漏出去。显然水比浆糊要泄漏得快。同理,对于双螺杆泵,粘度大的流体比粘度小的液体的泄漏要小,泄漏量与介质粘度有一定的比例关系。综上所述,要综合地考虑以上各种因素,通过一系列的计算才能精确地知道泵的实际流量是否符合工况要求。The influence of the viscosity of 1.3 v: just think: will clear water and the volume of the sticky paste with the e leak out from the funnel type of container.Obviously water leak faster than paste.Similarly, for double screw pump, the viscosity of the fluid is larger than that of low viscosity liquid leakage, leakage and the proportion of medium viscosity have a certain relationship.Above all, should be synthetically considered the above factors, through a series of calculations to accurately know the actual flow of the pump is in accordance with the working condition requirements.
2.压力 △P:
与离心泵不同,双螺杆泵的工作压力 △P由出口负载决定,即出口阻力来决定。出口阻力与泵的出口处的压力是匹配的,出口阻力越大,工作压力也越大。若想知道压力,则需要用流体力学的知识对出口阻力精确的计算。供应W2.1zk24w73双螺杆泵,油脂输送泵,泵体采用铸铁材质,4套机封
输送汽车胶泵 | NYP220高粘度泵 | 广州金发科技股份有限公司 |
输送道路密封胶泵 | NYP220B-RU-T1-J-W12高粘度泵 | 巨化集团公司 |
输送耐温耐酸密封胶泵 | NYP220B-RU-T2-J-W12高粘度泵 | 宁波乐金甬兴化工有限公司 |
输送聚氨酯密封胶泵 | NYP220B-LU-T2-J-W12高粘度泵 | 蓝星化工新材料股份有限公司 |
输送聚氨酯粘接剂泵 | NYP220B高粘度泵 | 上海宝钢化工有限公司 |
渣油上料泵 | NYP220B-RU-T1-W12高粘度泵 | 双钱集团股份有限公司 |
消防泡沫灭火剂泵 | SNH660R54E6.7W1三螺杆泵 | 江苏恒力化纤有限公司 |
输送泡沫原液泵 | NYP220B-RU-T1-J-W12高粘度泵 | 烟台万华聚氨酯股份有限公司 |
原油供油泵 | SNS120R42U12.1W21三螺杆泵 | 天津新港船舶重工有限责任公司 |
原油污油回收泵 | SNH940R46E6.7W2三螺杆泵 | 广州黄埔造船厂 |
螺杆式输油泵 | SNH940R46E15YW3三螺杆泵 | 山东省威海船厂 |
输送油浆泵 | SNH940R42U12.1W21三螺杆泵 | 江西江洲联合造船有限责任公司 |
输送重质油泵 | SNH940R42E6.7W1三螺杆泵 | 中国正新橡胶公司 |
输送含有污水泵 | G70-1P-W102单螺杆泵 | 青岛丽东化工有限公司 |
输送表面活性剂泵 | G35-1V-W102单螺杆泵 | 珠海BP化工有限公司 |
粘合剂卸料泵 | NYP220B-LU-T1-W12高粘度泵 | 正和集团股份有限公司 |
双出口三螺杆泵 | 3G45×4C2三螺杆泵 | 陕西延安发电厂 |
立挂式三螺杆泵 | 3G45×6C2三螺杆泵 | 陕西韩城发电厂 |
输送热熔胶泵 | NYP-440不锈钢高粘度泵 | 宜昌兴发集团有限责任公司 |
输送压敏胶泵 | NYP110-RU-T2-J-W51高粘度泵 | 中国北方化学工业(集团)有限责任公司 |
输送酒精胶泵 | NYP220B-LU-T1-J-W12高粘度泵 | 风神轮胎股份有限公司 |
输送固体胶泵 | NYP110-RU-T1-J-W11高粘度泵 | 四川龙集团有限责任公司 |
高粘度固体胶泵 | NYP110-LU-T1-J-W11高粘度泵 | 广东华润涂料有限公司 |
输送脱漆脱胶剂泵 | NYP110保温高粘度泵 | 云南南磷集团股份有限公司 |
环保型胶类泵 | NYP220B高粘度泵 | 湖北新洋丰肥业股份有限公司 |
输送防水胶泵 | NYP220B-LU-T1-J-W12高粘度泵 | 山东西水橡胶集团有限公司 |
输送合成胶粘剂泵 | NYP220B-RU-T1-J-W12高粘度泵 | 红太阳集团有限公司 |
输送聚氨酯密封胶泵 | NYP320B-RU-T2-W51高粘度泵 | 浙江远东化纤集团有限公司 |
输送耐高温硅胶泵 | NYP220保温高粘度泵 | 四川化工控股(集团)有限责任公司 |
搜好货厂家河北远东泵业制造有限公司为您提供河北远东泵业 供应W2.1zk24Z1M1W73 双螺杆泵 油脂输送泵 泵体采用铸铁材质的详细产品价格、产品图片等产品介绍信息,您可以直接联系厂家获取河北远东泵业 供应W2.1zk24Z1M1W73 双螺杆泵 油脂输送泵 泵体采用铸铁材质的具体资料,联系时请说明是在搜好货网看到的。
品牌 : | 河北远东 |
型号 : | W2.1zk24Z1M1W73 |
类型 : | 螺杆泵 |
材质 : | 铸铁 |
驱动方式 : | 电动 |
流量 : | 4.1 |
性能 : | 自动 |
输送介质 : | 油泵 |
泵轴位置 : | 卧式 |
叶轮数目 : | 单级 |
扬程 : | 20 |
转速 : | 950 |
吸入口径 : | 40 |
排出口径 : | 40 |
效率 : | 98 |
输出流量 : | 4.1 |
重量 : | 80 |
电压 : | 380 |
功率 : | 1.7 |
用途 : | 增压泵 |
是否跨境货源 : | 否 |
联 系 人
联系电话
采购说明