河北远东泵业 聚氨酯发泡剂专用泵 2CY-18/2.5 齿轮泵 薄利多销无条件退货

河北远东泵业 聚氨酯发泡剂专用泵  2CY-18/2.5  齿轮泵  薄利多销无条件退货

   用途:

   2CY齿轮泵适用于输送不含固体颗粒和纤维,无腐蚀性,温度不高于200℃,粘度为5×10-6～.5×10-3m2/s(5-1500cSt)的润滑油或性质类似润滑油的其他液体以及用于液压转动系统. 2 cy gear pump is suitable for conveying containing no solid particles and fibers, non-corrosive, temperature is not higher than 200℃, the viscosity of 5 x 10-6 ~. 5 x 10-3 m2 / s (5 to 1500 CST) the nature of the lubricating oil or other similar oil liquid and used for hydraulic rotation system.

   工作原理

   2CY齿轮油泵系容积式泵,主,被动齿轮与泵体,左右泵盖组成进油,出油二个封闭空间,当齿轮转动时,进油腔的容积,由于啮合齿不断脱开,而由小变大.形成真空,将液体吸入,有齿谷带往油腔,而出油腔容积,由于啮合齿的不断进入啮合而大变小,油液受压缩而被排出,从而达到输送油料的目的. 2 cy gear oil pump is a positive displacement pump, the main, driven gear and the pump body, pump cover around of feed, oil two closed space, when the gears, the oil cavity, the volume of meshing teeth off constantly, and change from small to large. The formation of a vacuum, the liquid suction, toothed valley to the oil cavity, and the volume of the oil cavity, due to the constant into the mesh of the meshing teeth and large to small, oil is displaced by compression, so as to achieve the aim of oil.

   结构特点

   本系列齿轮泵主要有齿轮,轴,泵体,泵盖,轴承套,轴端密封等组成.齿轮经氮化处理有较高的硬度和耐磨性.与轴一同安装在可更换的轴套内运转.泵内全部零件的润滑均在泵工作时利用输送介质而自动达到.泵内四个轴承套在泵内浮动安装,随工作压力大小自动调整端面间隙,因此泵的压力稳定,输出流量脉动小,溶积效率高.从主轴外伸端向泵看,为顺时针旋转. This series gear pump are mainly gear, shaft, pump body, pump cover, bearings, shaft end seal, etc. The gear after nitriding treatment had a higher hardness and wear resistance. With the shaft installed in the replaceable shaft sleeve. In all parts of the lubrication pump are using the transmission medium and automatic for when the pump work. Four bearing sleeve inside the pump in the pump float installation, along with the work pressure automatically adjusts end clearance, so the pump pressure stability, the output flow pulsation is small, high volume efficiency. From the main shaft overhang end to the pump, for clockwise.

   应用范围

   在输油系统中可用作传输,增压泵; In the oil system can be used as a transport, booster pump;

   在燃油系统中可用作输送,加压,喷射的燃油泵; In the fuel system can be used as a transport, pressure, jet fuel pump;

   在液压传动系统中可用作提供液压动力的液压泵; In the hydraulic drive system can be used as a hydraulic pump of hydraulic power;

    在一切工业领域中,均可作润滑油泵用;In all industrial areas, can be used as lubricating oil pump;

   使用与安装: Use and installation:

1、机组应安装在水平水泥基础上，用地脚螺栓固定。1, the unit should be installed in a horizontal cement, on the basis of land use fixed bolt.

2、右联轴器应同轴，安装完成后，转动联轴器确认运转顺畅无负压力现象后，方可进入运行。2, should right coupling coaxial, after the installation is complete, turn the coupling confirmed after running smoothly without negative pressure phenomenon, may run into.

3、泵不适合输送不洁油液，故在进口管端应设滤油器。3, the pump is not suitable for conveying impurity oil, therefore, at the inlet pipe should be set oil filter.

4、泵无安全阀，建议在排油管路中，设安全阀，以确保系统安全运行。4 no relief valve, pump, it is suggested that in the discharge of oil pipeline, a safety valve, and to ensure the safe operation of the system.

5、泵的安装高度，不超过允许吸上高度。5, pump installation height, no more than allow on the suction height.

6、泵的转向规定：从泵端向电机看，旋转方向为逆时针。6, pump steering regulation: look from the pump to the motor, for counterclockwise rotation direction.

  工作注意事项: Work matters needing attention:

1、开机前应检查泵轴转动是否灵活，有无卡阻现象，进出口管道上的阀门是否开启，泵的旋转方向是否正确。1, should check whether the pump shaft rotation is flexible, before starting the presence of jam phenomenon, import and export pipeline valve is open, the direction of rotation of the pump is correct.

2、长时间没有使用的泵开机前应向泵腔中注入一定量的润滑液，以减少泵在吸油过程中的干摩擦，并可提高泵自吸性能。2, long time no use the pump to the pump before starting the cavity inject a certain amount of lubricant to reduce the pump in the dry friction in the process of oil absorption, and can improve the performance of pump.

3、开机后如有不正常的噪音或过热现象，应立即停车检查。3, after the boot if there is any abnormal noise or overheating phenomenon, should immediately stop check.

4、检查泵轴端有无泄露现象，如：对填料密封应适当调紧压紧盖、其他密封则应拆机检查。4, check whether there is any leakage on the pump shaft end phenomenon, such as: the packing should be properly tighten clamp cover and other sealing should teardown check.5、若输送热油，在开车时应均匀预热，预热是利用被输送的介质不断通过泵体进行的。5, if conveying hot oil, while driving should be uniform preheating, preheating is to use the media constantly through the pump body to be delivered.

6、泵停机时，首先切断电源，然后关闭进出口管道上的阀门，避免造成泵倒转。6, when the pump stop, cut off power supply first, then close the import and export pipeline valve, avoid to cause back pump.

 

   使用与安装:1、机组应安装在水平水泥基础上，用地脚螺栓固定。2、右联轴器应同轴，安装完成后，转动联轴器确认运转顺畅无负压力现象后，方可进入运行。3、泵不适合输送不洁油液，故在进口管端应设滤油器。4、泵无安全阀，建议在排油管路中，设安全阀，以确保系统安全运行。5、泵的安装高度，不超过允许吸上高度。6、泵的转向规定：从泵端向电机看，旋转方向为逆时针。Use and installation: 1, the unit should be installed in a horizontal cement, on the basis of land use fixed bolt.2, should right coupling coaxial, after the installation is complete, turn the coupling confirmed after running smoothly without negative pressure phenomenon, may run into.3, the pump is not suitable for conveying impurity oil, therefore, at the inlet pipe should be set oil filter.4 no relief valve, pump, it is suggested that in the discharge of oil pipeline, a safety valve, and to ensure the safe operation of the system.5, pump installation height, no more than allow on the suction height.6, pump steering regulation: look from the pump to the motor, for counterclockwise rotation direction.

 

 

   工作原理:本泵系容积式泵，主、被动齿轮与泵体、左右泵盖组成进油、出油二个封闭空间，当齿轮转动时，进油腔的容积，由于啮合齿不断脱开，而由小变大。形成真空，将液体吸入，有齿谷带往油腔，而出油腔容积，由于啮合齿的不断进入啮合而大变小，油液受压缩而被排出，从而达到输送油料的目的。Working principle: this pump is a positive displacement pump, the main around, passive gear and pump body, pump cover of the oil, the oil two closed space, when the gears, the oil cavity, the volume of meshing teeth off constantly, and changes from small to big.Form a vacuum, the liquid suction, toothed valley to the oil cavity, the volume of the oil cavity, due to the constant into the mesh of the meshing teeth and large to small, oil is displaced by compression, so as to achieve the aim of oil.

 

   用途:2CY齿轮泵主要用于各种机械设备中的润滑系统中输送润滑油。Purpose: 2 cy gear pump is mainly used for all kinds of mechanical equipment of conveying lubricating oil lubrication system.

   

   工作原理:本泵系容积式泵，主、被动齿轮与泵体、左右泵盖组成进油、出油二个封闭空间，当齿轮转动时，进油腔的容积，由于啮合齿不断脱开，而由小变大。形成真空，将液体吸入，有齿谷带往油腔，而出油腔容积，由于啮合齿的不断进入啮合而大变小，油液受压缩而被排出，从而达到输送油料的目的。Working principle: this pump is a positive displacement pump, the main around, passive gear and pump body, pump cover of the oil, the oil two closed space, when the gears, the oil cavity, the volume of meshing teeth off constantly, and changes from small to big.Form a vacuum, the liquid suction, toothed valley to the oil cavity, the volume of the oil cavity, due to the constant into the mesh of the meshing teeth and large to small, oil is displaced by compression, so as to achieve the aim of oil.

   

   结构说明:本系列泵主要由：左、右泵盖、泵体、主、被动齿轮轴、轴套、油封等零件组成。Structure description: this series of pump is mainly composed of: left, right, pump cover, pump body, , passive gear shaft, shaft sleeve, oil seal and other parts.

      河北远东泵业制造有限公司坐落于铸造名乡—河北省泊头市。公司占地面积38650平方米，建筑面积20300平方米，是国内著名的集设计、铸造、生产、销售、服务于一体的容积泵专业制造厂家。公司始建于1984年,有二十几年专业研制经验。目前产品设计采用国际先进水平实体设计软件；产品研发、制造、检验、交付按照ISO9001质量管理体系控制过程质量；产品制造广泛使用加工中心、数控机床、专用精机、高精设备；检测设备拥有显微镜、渐开线检测仪、光学投影仪、万能测齿仪、脉冲辉光离子氮化炉等大型检测设备，并建有国家B级试验站。本厂以一流的产品水平、优质的售后服务、恪守信用而在市场上倍受欢迎，产品畅销不衰，赢得了用户的普遍赞誉。公司已通过ISO9001：2000国际质量体系认证，中国船级社CCS型式认证，法国船级社BV产品工厂认证，美国船级社ABS产品质量认证，中国渔业船舶检验局船用泵认证,成为中石油物资资源市场成员、中石化物资资源市场成员。河北省知名产品生产企业，船用泵产品承制企业。Hebei far east pump industry manufacturing co., LTD is located in botou city, hebei province, a casting of the township.The company covers an area of 38650 square meters, construction area of 20300 square meters, is the domestic famous design, casting, production, sales and service in one of the positive displacement pump professional manufacturer.Company was founded in 1984, has 20 years experience in professional development.The current product design adopts the international advanced level entity design software;Product research and development, manufacture, inspection, delivery, in accordance with the ISO9001 quality management system of process quality control;Widely used products manufacturing processing center, numerical control machine tools, precision machine, high precision equipment;Testing equipment has universal tool microscope, involute tester, optical projector, universal gear tester, pulse glow ion nitriding furnace and other large-scale testing equipment, and built national B level test station.The factory with the first-class products, excellent after-sales service, abide by credit and popular in the market, the products sell well and win the user\'s universal praise.The company has passed ISO9001:2000 international quality system certification, China classification society CCS type approval, bureau veritas BV products factory certification, the United States classification society ABS product quality certification, China\'s Marine fishing vessel inspection bureau pump certification, has been a member of the material resource market in oil, sinopec material resources market member.Well-known products production enterprise in hebei province, Marine pump products enterprises.

   公司以“泊远东”牌齿轮泵，螺杆泵为主导产品，涉及21个系列，4200多种规格，年生产能力达43000多台（套）。产品行销油田、化工、电力、船舶、冶金、食品等各大行业。产品除满足国内客商的需求外，部分出口至东南亚、美洲、欧洲等国家和地区。公司在设有30多个分支机构，并建立了完善的营销服务网络，拥有一支庞大敬业的营销服务队伍，可为广大客户提供优质的服务。 公司以严谨的质量体系、先进的生产设备、完善的检测手段、丰富的制造经验、务真求实的远东团队，来有效保证产品质量。以满腔真诚期待与国内外各界人士携手铸就多方共赢的辉煌。Company to "moored far east" brand gear pump, screw pump for the leading product, involves the 21 series, more than 4200 kinds of specifications, annual production capacity of more than 43000 Taiwan (sets).Product marketing oilfield, chemical industry, electric power, shipbuilding, metallurgy, food and other major industry.Products in addition to meet the needs of domestic customers, some exports to southeast Asia, the americas, Europe and other countries and regions.The company has more than 30 branches in major cities throughout the country, and established a perfect marketing service network, has a large professional marketing services team, can provide the high quality service for the customers.Companies with strict quality system, advanced production equipment, perfect detection means, rich manufacturing experience and WuZhen strives for the far east team, to effectively ensure the quality of products.To sincerely look forward to working with people from all walks of life both at home and abroad hand in hand to own a bright multi-win-win situation.

 

 

   我公司是一个生产齿轮油泵和螺杆泵的专业公司。公司拥有各种设备80台,主要设备有：C6140 CW6163C车床24台，TX611C/4镗床2台，M131M7130磨床8台，C125A立车2台，Y318K Y3150E滚齿机6台，E3050X16/1摇臂钻床2台，E5163立式钻床2台，B1-400万能铣床3台，螺杆泵转子专用QH2-007铣床1台，半自动螺旋转子QH2-029B铣床2台，X53K立铣3台，半自动螺旋转子QH2-031 QH2-032磨刃机台。My company is a company specialized in the production of gear oil pump and screw pump.Company has 80 sets of various devices, the main equipment are: C6140 CW6163C24 sets of lathe, TX611C/boring machine 2 units,4 M131M 7130 grinding machine 8 units, C125Aset, 2 sets, Y318K Y3150E hobbing machine 6 units, E3050X16/1 radial drilling machine 2 sets, E5163 vertical drilling machine 2 sets, B1-400 universal milling machine 3 units, screw pump rotor 1 QH2-007 milling machine, semi-automatic screw rotor QH2-029 - b milling machine 2 sets, X53K three vertical milling, semi-automatic screw rotor QH2 QH2-031-031 edge grinding machine is used.

   我公司拥有省计量局制试验台1台，自制试验台3台，使生产产品从原材料投入到产成品出厂实现了全过程检测。产品出厂合格率100%，具备较强的综合配套制造能力。理化试验室、长度计量室是国家计量确认合格单位，使产品从原材料投入到产成品出厂实现了全过程检测。产品出厂合格率100%，具备较强的综合配套制造能力，公司年可生产各种泵6000多台。My company has the province system test bench 1 bureau of standard measurement, homemade test-bed 3 units, production of products from raw materials into finished goods factory implements the whole process of detection.Product factory qualified rate 100%, have strong ability of comprehensive manufacturing.Physical and chemical laboratory, length measuring room is the national metrological confirmation unit, make our products from raw materials into finished goods factory implements the whole process of detection.Product factory qualified rate 100%, have strong comprehensive manufacturing capacity, company can produce all kinds of pump in more than 6000 units.

河北远东泵业 聚氨酯发泡剂专用泵  2CY-18/2.5  齿轮泵  薄利多销无条件退货

输送粘胶剂泵	NYP110不锈钢高粘度泵	杭州之江有机硅有限公司
输送聚醚泵	NYP220B-RU-T1-J-W12高粘度泵	帝人聚碳酸脂有限公司
聚醚输送泵	NYP220B高粘度泵	甘肃金昌工业集团有限公司
聚氨酯发泡剂专用泵	YCB20齿轮泵	华能南通电厂
输送燃料油泵	3GCLS100*2W2三螺杆泵	南通港闸船舶制造有限公司
聚氨酯发泡剂专用泵	3GCL85*2W2三螺杆泵	青岛现代造船有限公司
输送原油泵	3GCL70*2W2三螺杆泵	临海市江海造船有限公司
燃油滑油污油泵	3GCL110*2W21三螺杆泵	华能威海电厂
主机滑油泵	3GR25*4W2三螺杆泵	浙江宏信船舶有限公司
电动螺杆泵	3GR25*4W2三螺杆泵	华能南京电厂
滑油输送泵	3GR110*4W21三螺杆泵	华能南通电厂
高粘度液体泵	G50-1V-W102单螺杆泵	江苏金桐工业有限公司
污油回收泵	3GR25*6w21三螺杆泵	当阳市华强有限公司
焦油输送泵	3GR25*6W2三螺杆泵	朝阳浪马轮胎有限责任公司
重油装船泵	3GR25*6W2三螺杆泵	陵县绿源有限责任公司
重油输送泵	3GR25*6W2三螺杆泵	重庆长寿有限责任公司
喷油泵	3GCL110*2W2三螺杆泵	明盛控股集团有限公司
稠油输送泵	3GR30*4W21三螺杆泵	江苏丰山集团有限公司
聚氨酯发泡剂专用泵	3GR30*4W21三螺杆泵	辽宁瑞兴集团有限公司
燃料油卸车泵	3GR30*4W21三螺杆泵	长治霍家工业有限公司
电动燃油泵	3GR30*4W2三螺杆泵	广州珠江集团有限公司
电动污油泵	3GR30*4W2三螺杆泵	青岛国人集团有限公司
聚氨酯发泡剂专用泵	3G36*6AW21三螺杆泵	陕西榆林天然气有限责任公司

 

搜好货厂家河北远东泵业制造有限公司为您提供河北远东泵业 聚氨酯发泡剂专用泵 2CY-18/2.5 齿轮泵 薄利多销无条件退货的详细产品价格、产品图片等产品介绍信息，您可以直接联系厂家获取河北远东泵业 聚氨酯发泡剂专用泵 2CY-18/2.5 齿轮泵 薄利多销无条件退货的具体资料，联系时请说明是在搜好货网看到的。