河北远东泵业 水电站水轮机调速器控制油泵 润滑油输送泵 3G45x6C2 河北省优质产品

水电站水轮机调速器控制油泵3G45*6C2河北省优质产品

    尊敬的客户您好:    我们是河北远东泵业制造有限公司,公司已通过ISO9001：2000国际质量体系认证，中国船级社CCS型式认证，法国船级社BV产品工厂认证，美国船级社ABS产品质量认证，成为中石油物资资源市场成员、中石化物资资源市场成员，并列入《武器装备科研生产保密资格名录》可以承担军队系统装备部门的涉密武器装备科研生产合同项目。河北省知名产品生产企业，船用泵产品承制企业。我们的产品是：同样的价格我们的质量更优、同样的质量我们价格更低、同样的产品我们服务更好。、螺旋角：5、结构特性与轴封：

符号	结构说明		适用范围
U	内置滚动轴承	-	介质润滑性良好，温度小于80℃
1.0	骨架油封	-	介质润滑性良好，立式安装
2.0	2机械密封材料组合为硬对石墨	0表示密封的结构型式（不同型式机封按顺序号依次排列，如2.1，2.2）	介质润滑性良好，温度小于80℃

 

6、材料组合：

材料组合代码	泵体	衬套	材料组合代码	泵体	衬套
W11	HT200	HT200	W14	HT200	ZL109
W12	HT200	ZCuSn5Pb5Zn5	W22	焊接Q235	ZCuSn5Pb5Zn5

7、特殊要求：S表示用户特殊要求，据不同要求分别以S1～S10区分表示，具体序号由工厂提供。

水电站水轮机调速器控制油泵3G45*6C2河北省优质产品

●3G三螺杆泵工作原理:

　　3G型三螺杆泵是转子型容积泵，适于输送各种不含固体颗粒，无腐蚀性油类及类似油的润滑性液体、输送液体粘度2~760mm2/s，温度不超过80℃,超过80℃可用高温泵3GW型。3 g type is three screw pump rotor type positive displacement pump, is suitable for conveying various not containing solid particles, non-corrosive oil lubricity and similar oil liquid, conveying liquid viscosity was 2 to 760 / s, temperature not over 80℃, more than 80℃high temperature pump available 3 gw type.

   3G型三螺杆具有多种结构，一般小流量泵衬套和泵体合为一个，可以卧式和立式安装。进油口方向可相隔90°任意安装，轴封多数为机构密封。中等流量以上泵，衬套为一个单独的零件固定于泵体内，螺杆轴端装有平衡环以液力平衡其轴向力。一般结构为卧式。进油口方向亦可以相隔90°任意安装。改变泵体后可制成立式。轴封根据情况有机械密封和软填料密封两种结构。

   3G型三螺杆泵轴伸支承较小，应由原动机经弹性联轴器直接驱动，不得用皮带轮等会产生额外径向力较大的传动方式传动。3 g type three-screw pump shaft and bearing is small, should be driven by a prime mover directly by the elastic coupling, shall not be used pulley will produce additional radial force large transmission way.

●3G三螺杆泵输送各种油类时应注意事项：When conveying various oil matters should be paid attention to:

   1、输送40~150mm2/s的油类最合适，允许按泵的最高工作压力使用。2、输送40mm2/s以下的油类，为保证泵的流量及寿命应降压使用。3、输送150mm2/s以上的油类，且进油管道过长，弯头过多，泵工作时如产生噪音或振动现象，则应考虑更换低一级转速的电机运转或缩短吸入管道，减少弯头。

 ●3G型三螺杆泵安装要求:3 g type three-screw pump installation requirements:

   1、安装前应检查泵的油封是否良好，并检查泵在运输中是否损坏，可用手转动联轴器是否有卡劲现象，如有则应拆泵进行清洗，修理和校正。1, before installation should check whether the oil seal of the pump is good, and check the pump is damaged in transportation, turn the coupling usable hand card trouble phenomenon, if there is any should tear open pump for cleaning, repair and calibration.2、安装泵的进油和排油管道时，其管径不得小于泵的进油和出油口口径，进油管道不得过长，弯头不得过多，否则将影响泵的工作状态。2, installation of pump suction and discharge of oil pipe, the pipe diameter shall not be less than the oil inlet of the pump and the oil outlet diameter, inlet pipe shall not be too long, elbow shall not too much, otherwise will affect the pump working condition.3、当有两台以上的泵安装在同一条主管线上，为便于泵的启动，在近泵的排油管上必须安装逆止阀。3, when more than two head of pump installed in the e line, to facilitate pump start-up, in close to the oil drain pump must be installed on a non-return valve.4、对于在较高温度（指60℃以上）下输送粘度大的油类（如：重油）的备用泵，必须是热备用泵，否则泵在低温下启动会造成电机过载或泵损坏。（建议在靠近泵的排油管上的逆止阀旁，并联安装一个小回流阀，对备用泵可微启回流阀，使泵缓慢逆转，其逆转速≤100转/分，使部分热油经常流过泵内，达到泵热备用目的）。4, for under high temperature (above 60℃) conveying the viscosity of oil (such as: heavy oil) of the standby pump, it must be hot standby pump, otherwise the pump at low temperature can cause the damage of motor overload or pump.(suggest near the exhaust non-return valve on the tubing pump, a small return valve installed in parallel, differentiable and the backflow preventer to standby pump, the pump slow reversal, the reverse speed 100 r/min or less, often make some hot oil flows through the pump, to pump hot standby purposes).5、输送介质内含有机械杂质。将严重影响泵的运转和降低使用寿命，因此在泵安装前，必须仔细清除进油管内的焊渣，沙粒等杂质，并应在进油管道靠近泵处安装滤器，滤器网孔大小，可根据工作情况及介质粘度确定。（一般可用40~80目网），过滤面积一般不得小于进油管横截面积的20倍。5, mechanical impurity is contained within the transmission medium.Will seriously affect the operation and reduce the service life of pump, so before the pump installation, must be carefully clean up the feed tube welding slag, impurities such as grains of sand, and shall be installed in the inlet pipe near the pump filter, filter mesh size, is decided according to the working condition and medium viscosity.Available (40 ~ 80 mesh net), filter area generally shall not be less than 20 times into the cross-sectional area of the tubing 6、尽量在泵进油和排油口处的螺纹孔上连接压力表和真空表，以便于观察泵的运转状态。6, as far as possible in the pump suction and discharge of oil on the threaded hole mouth connect pressure gauge and vacuum gauge, in order to observe the pump running state.7、原动机与泵的转轴必须在同一中心线上，可用直尺测隙规在联轴器圆周上间隔90°处检查。8、原动机与泵的转向必须一致，严格禁止原动机驱动泵逆转。电机接线时，应先脱开电机与泵的联轴器，对电机作试运转。使其转向与泵的转向标志一致。7, prime mover and the pump shaft must be in the e center line, available ruler feeler gauge in the coupling of the circumference of a circle by 90°in check.8, steering engine and pump must be consistent, strictly prohibited prime motor driven pump reversal.Electrical wiring, should first release coupling of motor and pump, a test run on the motor.The steering pump and steering sign agreement

水电站水轮机调速器控制油泵3G45*6C2河北省优质产品

●水电行业业绩:

1.安徽省淮北发电厂

泵型号:3G60*4C压力4.0Mpa,流量13.2m3/h,配用电机22kw-4

      3G100*4C压力4.0Mpa,流量48.42m3/h,配用电机90kw-4

2.湘潭发电有限责任公司

泵型号:3G85*4C压力4.0Mpa,流量43.2m3/h,配用电机75kw-4

      3G85*42压力4.0Mpa,流量43.2m3/h,配用电机75kw-4

3.陕西渭河发电厂

泵型号:3G45*3C2压力1.0Mpa,流量6.72m3/h,配用电机4kw-4

      3G70*3C压力1.0Mpa,流量16.02m3/h,配用电机7.5kw-4

4.广西岩滩水电厂

泵型号:3G90*3C2压力1.0Mpa,流量54.72m3/h,配用电机30kw-4

      3G80*3C压力1.0Mpa,流量35.04m3/h,配用电机15kw-4

5.陈村水力发电厂

泵型号: 3G45*4G压力4.0Mpa,流量11.1m3/h,配用电机18.5kw-4

       3G90*4GR46U1.0W11压力:4.0Mpa,流量51.48m3/h,配用电机90kw-4

6.王快水电厂

泵型号: 3G55*4G40U1.0W11压力1.0Mpa,流量9.72m3/h,配用电机5.5kw-4

       3G60*4GR46U1.0W11压力1.0Mpa,流量16.26m3/h,配用电机7.5kw-4

7.张家界水电开发公司

泵型号: 3G85*4G46U1.0W11压力1.0Mpa,流量48m3/h,配用电机22kw-4

       3G100*4GR54U1.0W11压力1.0Mpa,流量100.5m3/h,配用电机45kw-4

8贺龙水电厂

泵型号: 3G80*4G44U1.0W11压力1.0Mpa,流量35.58m3/h,配用电机15kw-4

       3G70*4GR54U1.0W11压力1.0Mpa,流量33.66m3/h,配用电机15kw-4

9.鱼潭水电厂

泵型号: 3G80*4G44U1.0W11压力1.0Mpa,流量35.58m3/h,配用电机15kw-4

       3G70*4GR54U1.0W11压力1.0Mpa,流量33.66m3/h,配用电机15kw-4

10.陕西石泉水力发电厂

泵型号: 3G55*4G46U1.0W11压力1.0Mpa,流量12.18m3/h,配用电机5.5kw-4

       3G70*4GR54U1.0W11压力1.0Mpa,流量33.66m3/h,配用电机15kw-4

水电站水轮机调速器控制油泵3G45*6C2河北省优质产品

搜好货厂家河北远东泵业制造有限公司为您提供河北远东泵业 水电站水轮机调速器控制油泵 润滑油输送泵 3G45x6C2 河北省优质产品的详细产品价格、产品图片等产品介绍信息，您可以直接联系厂家获取河北远东泵业 水电站水轮机调速器控制油泵 润滑油输送泵 3G45x6C2 河北省优质产品的具体资料，联系时请说明是在搜好货网看到的。