KCB-18.3齿轮泵作为原油输送泵流量18.3L/min,压力:1.45Mpa

KCB-18.3齿轮泵作为原油输送泵流量18.3L/min,压力:1.45Mpa

KCB-18.3齿轮泵作为原油输送泵流量18.3L/min,压力:1.45Mpa

 KCB-18.3齿轮泵作为原油输送泵流量18.3L/min,压力:1.45Mpa

尊敬的客户您好:

我们是河北远东泵业制造有限公司,公司已通过ISO9001：2000国际质量体系认证，中国船级社CCS型式认证，法国船级社BV产品工厂认证，美国船级社ABS产品质量认证，成为中石油物资资源市场成员、中石化物资资源市场成员，并列入武器装备科研生产保密资格名录可以承担军队系统装备部门的涉密武器装备科研生产合同项目。河北省知名产品生产企业，船用泵产品承制企业。我们的产品是：同样的价格我们的质量更优、同样的质量我们价格更低、同样的产品我们服务更好。

　kcb齿轮泵安装: KCB gear pump installation:

 

　　1、泵安装前应检查泵和电机在运输过程中是否受到损坏，如电机是否受潮，泵的进出口防尘盖是否损坏而使污物进入泵腔内等。1, before the pump installation, should check the pump and motor is damaged during the transit, whether be affected with damp be affected with damp such as motor, pump the import and export of dust cover for damage and make the dirt into the pump chamber, etc.

 

　　2、泵在搬运过程中，应选择合适起吊位置，减少泵的变形。2, pump in the process of handling, should choose appropriate lifting position, reduce the deformation of the pump.

 

　　3、泵的底座应固定在牢固的基础上，以免产生振动影响泵的正常工作。3, the base of the pump should be fixed on the basis of the strong, so as to avoid vibration influence the normal work of the pump.

 

　　4、泵的进出口管路应清理干净不得存有硬颗粒的报告杂物。4, import and export of pipeline of pump should be cleaned up shall not have the report of hard particles sundry.

 

　　5、管路口径一般不小于泵的进出口径，进油管路应尽量短，并减少弯路。必要时在进油口安装金属过滤器，过滤器的有效面积不应小于管道过流面积的三倍。5, pipe diameter is generally not less than the in and out of the caliber of pump, the oil pipeline should be short, as far as possible and less detours.When necessary, metal filter is installed on oil inlet filter effective area should not be less than three times of pipe flow area.

 

　　6、安装时，不得用泵来承担管路的重量。7、用手转动联轴器，泵应转动灵活，不得有过紧或轻重不均现象，如有应立即排除。

6, when installation, must not use the pump to bear the weight of the line.7, turn the coupling with the hand, the pump should be flexible rotation, can not have too tight or weight uneven phenomenon, should immediately ruled out.

　　kcb齿轮泵的开机: KCB gear pump of the boot:

　　1、开机前应检查泵轴转动是否灵活，有无卡阻现象，进出口管道上的阀门是否开启，泵的转动方向是否正确。1, should check whether the pump shaft rotation is flexible, before starting the presence of jam phenomenon, import and export pipeline valve is open, the pump rotation direction is correct.

　　2、长时间没有使用的泵开机前应向泵腔中注入一定量的润滑液，以减少泵在吸油过程中的干摩擦，并可提高泵的自吸性能。2, long time no use the pump to the pump before starting the cavity inject a certain amount of lubricant to reduce the pump in the dry friction in the process of oil absorption, and can improve the self-priming performance of pump.

　　3、开机后如有不正常的噪音或过热现象，应立即停车检查。3, after the boot if there is any abnormal noise or overheating phenomenon, should immediately stop check.

　　4、检查泵轴端有无泄漏现象，如：对填料密封应适当调紧压紧盖，其它密封则应拆机检查；4, check whether there is any leakage on the pump shaft end phenomenon, such as: the packing should be properly tighten clamp cover, other sealing should teardown check;

　　5、若输送热油，在开机时应均匀预热，预热是利用被输送的介质不断通过泵体进行的。预热标准：吸入口的油温不得高于泵体温度40，预热的升温速度控制在＜40/h，在预热时应将固定泵体的螺栓松开，预热完毕，将其拧紧。在预热过程中，应注意观察泵的运行情况，以但发生不良情况，应立即停泵检查。5, if conveying hot oil, the boot should be uniform preheating, preheating is to use the media constantly through the pump body to be delivered.Preheat standard: the inlet oil temperature shall not be higher than the pump body temperature 40, the preheating temperature speed control in the < 40/ h, when the preheating bolts should be fixed pump body loosen, preheating and tighten it.Should be paid attention to in the process of preheating, observe the running situation of the pump, with adverse event, however, should immediately stop check pump.

 

　　6、泵停机后，首先切断电源，然后关闭进出口管道上的阀门，避免造成泵倒转。After six, pump stop, cut off power supply first, then close the import and export pipeline valve, avoid to cause back pump.

 

　　7、泵经过长期使用，压力流量有明显下降时，应拆泵检查，更换其己磨损的零件。　　

KCB-18.3齿轮泵作为原油输送泵流量18.3L/min,压力:1.45Mpa

搜好货厂家河北远东泵业制造有限公司为您提供KCB-18.3齿轮泵作为原油输送泵流量18.3L/min,压力:1.45Mpa的详细产品价格、产品图片等产品介绍信息，您可以直接联系厂家获取KCB-18.3齿轮泵作为原油输送泵流量18.3L/min,压力:1.45Mpa的具体资料，联系时请说明是在搜好货网看到的。