沥青路面用纤维吸油率测定仪 XYL 荣计达

一、产品简介：

纤维吸油率测定仪是检测仪器，用于公路工程沥青路面用纤维作吸油率指标测定之用。

Product introduction:

Fiber oil absorption rate tester is a testing instrument for measuring the oil absorption index of fibers used in highway engineering asphalt pavement.

二、技术参数：

★振动时间：0-60min

★电源：220v50HZ

★试样筛规格：0.5mm孔径/直径100MM

★振动速度：240次/分钟

★振动振幅32mm

★振动时间：可人为控制

★外形尺寸：55X28X50mm

★   重量：10kg

Technical parameters:

★ Vibration time: 0-60min

★ Power supply: 220v50HZ

★ Specification of sample sieve: 0.5mm aperture / diameter 100MM

★ Vibration speed: 240 times / minute

★ Vibration amplitude 32mm

★ Vibration time: can be controlled manually

★ Dimensions: 55X28X50mm

★ Weight: 10kg

三、产品特点：

★振动速度均匀，搅拌充分。

★采用时间继电器设置控制振动时间。

★度均匀，搅拌充分。

★可人工自行控制振动时间（通过开关机实现）

Third, product characteristics:

★ The vibration speed is uniform and the stirring is sufficient.

★ Use the time relay setting to control the vibration time.

★ The degree is uniform, and stir well.

★ The vibration time can be controlled manually (by switching on and off)

四、操作方法：

★基本模块

1，包含定标、测量、查询、设置四个模块。

2，操作简单，无需**人员来操作

3，参数设置——点击按钮仪器自动校正

4，测试结果自动保存在电脑中，可通过查询功能导出至Excel表格中进行分析。

★操作步骤

装样——称重——放样——测量——出结果（单个样品检测5分钟以内完成，多样品统筹时，平均第个样品2分钟）

★数据分析

数据分析主要是分析检测数据的准确性、稳定性、标准偏差等检测数据，同时通过检测 数据调整生产工艺流程，从而把上油率调整到zui佳状态，节约资源。

Fourth, the operation method:

★ Basic Module

1. Contains four modules: calibration, measurement, query and setting.

2, simple operation, no need for ** personnel to operate

3, parameter setting-click the button to automatically calibrate the instrument

4. The test results are automatically saved in the computer and can be exported to an Excel table for analysis through the query function.

★ operation steps

Loading—weighing—staking out—measurement—outcome results (single sample detection completed within 5 minutes, when multiple samples are coordinated, the average first sample is 2 minutes)

★ Data analysis

Data analysis mainly analyzes the test data such as accuracy, stability, standard deviation, etc. At the same time, the test data is used to adjust the production process to adjust the oiling rate to a good state and save resources.

五、使用方法：

★根据实验需要，称取相应质量的纤维、矿物油混合物，倒入仪器上的试样筛中。

★设定振动时间，插到220V、50Hz电源上，按下电源开关，使其处于“开”的位置。

★达到设定时间后，仪器自动停机并发出报警声。

★关掉电源开关，取下试样筛，称取试样筛和吸有矿物油的纤维的质量，按有关公式计算的吸油率指标。

★做二次试验时，重复上述步骤即可。

Five, use method:

★ According to the needs of the experiment, weigh the corresponding fiber and mineral oil mixture and pour it into the sample sieve on the instrument.

★ Set the vibration time, plug it into a 220V, 50Hz power supply, and press the power switch to make it "on".

★ After reaching the set time, the instrument will automatically stop and issue an alarm sound.

★ Turn off the power switch, remove the sample sieve, weigh the mass of the sample sieve and the fiber that absorbs mineral oil, and calculate the oil absorption index according to the relevant formula.

★ Repeat the above steps for the second test.

 

搜好货厂家上海荣计达仪器科技有限公司为您提供沥青路面用纤维吸油率测定仪 XYL 荣计达的详细产品价格、产品图片等产品介绍信息，您可以直接联系厂家获取沥青路面用纤维吸油率测定仪 XYL 荣计达的具体资料，联系时请说明是在搜好货网看到的。