恒创利 瓦楞纸板生产线 单瓦生产线 瓦楞机 液压支架

ⅰ、Structural features结构特点：

★This part is the main beam of the 20th channel, 16-beam, angle iron 63, column, etc. are connected.

本部分是主梁为20号槽钢、16号工字钢、63号角钢、立柱等连接而成。

★Both sides of the security fence, ladder , high-strength save people the word pedals, ensure the safety of personnel and easy to operate.

两侧均有安全护栏、梯子（用8号小槽钢制作）、高强度人字踏板，确保人员的工作安全以及操作方便。

★Pull the paper shaft surface tension axis, feeding shaft by grinding hard chrome plated.

牵纸轴、张紧轴、输纸轴等表面经磨削加工镀硬铬处理。

★Vacuum tension control, 5-inch suction tube, plus regulating valves, air flow can be infinitely adjustable.

真空吸附张力控制，吸风管5寸，加调节阀门，风量可无级可调。

★Dual front bezel correction guide column positioning, screw driver, fast and accurate positioning, walking steadily.

纠偏挡板前采用双导向柱定位，丝杠驱动，定位快速准确，行走平稳。

ⅱ、Roller diameter parameter辊类直径参数：

★Paper roll and a tension roller diameter:￠130mm         上纸辊及张紧辊直径：￠130mm      

★Conveying roller diameter：￠180mm                    输送辊直径：￠180mm

★Active tension roller diameter：￠85mm                  主动张紧辊直径：￠85mm      

★Diameter of over paper rollers and guide rollers：￠110mm 过纸辊及导纸辊直径：￠110mm

★Paper towing shaft diameter：￠110mm                  上纸拖带轴直径：￠110mm       

ⅲ、Powered motor parameters动力电机参数

★Corrugated single paper lift motor：2.2KW                单面瓦楞纸提升电机：2.2KW

★The bridge adsorption motor：2.2KW                     过桥吸附风机：2.2KW       

★Wide motor tune cardboard：250W                      调纸板宽幅电机：250W       

 

6、GM-12 Double glue machine二层涂胶机                         

ⅰ、Structural features结构特点：

★After the glue roller surface after quenching inner hole machining, grinding and dynamic balancing surface engraved with pit style textured, coating evenly, less consumption of plastic。

涂胶辊表面经调质后，内孔加工，做动平衡表面精磨并刻有凹坑式网纹，涂胶均匀，耗胶量少。

★Doctor roller surface by grinding and hard chromium plating.

刮胶辊表面经磨削加工并镀硬铬。

★other guide rollers with hard chrome plated.。其余导纸辊表面镀硬铬。

★Pressure roller with pneumatic lift, easy operation。压辊采用气动升降，操作灵活方便。

★ manually adjust scraping gap。手动调整涂刮间隙。

★glue roller ¢ 215mm、Doctor roll¢ 122mm、press paper roller¢ 122mm、preheat roller 270mm。涂胶辊¢ 215mm、匀胶辊¢ 122mm、压辊¢ 122mm、预热辊270mm。

★Electrical design, construction production process, follow the national standards, low failure rate, easy maintenance。

电器设计、生产施工工艺，遵循国家标准规范，故障率低，维护简单。

★Manual glue adjustment。手动调胶。

ⅱ、Technical parameter技术参数：

★Effective width：1800mm                         工作幅宽：1800mm           

★Operation direction：left or right（determined in accordance with customer plant）

操作方向：左置或右置（根据客户厂房确定）

★Design speed：100m/min                        设计速度：100m/min

★Gas supply system：0.4—0.9Mpa                 气源系统：0.4—0.9Mpa

★Preheat cylinder temperature range：150—200℃   预热缸温度范围：150—200℃     

★Steam pressure:0.8—1.2Mpa                     蒸汽压力：1.12—1.3Mpa

ⅲ、Roller diameter parameter辊类直径参数：

★Glue roller diameter：￠215mm                   涂胶辊直径：￠215mm               

★Doctor roller diameter：￠122mm                 定糊辊直径：￠122mm

★Lower preheating roll diameter：￠270mm         下预热辊直径：￠320mm             

★Under preheat roller diameter：￠270mm          上预热辊直径：￠270mm

★Over the paper roll diameter：￠85mm            过纸辊直径：￠85mm

ⅳ、Powered motor parameters动力电机参数：

★Glue roller initiative frequency motor：3KW         涂胶辊主动电机：    3KW            

★Sizing Reducer:：250W                          胶量调整减速机：    250W          

★Pressure roller clearance adjustment motor： 250W 压力辊间隙调整电机：  250W          

★Glue pump motor：2.2KW                        胶泵电机：2.2KW           

 

7、SM-10type double facer双面机                                  

ⅰ、Structural features结构特点：

★Heating plate surface by grinding treatment, hot plate width 600mm, a total of 12 heating plate and cooling 4 m。Heating plate with a container board production, in line with national standards for a class pressure vessel, with pressure vessel certificate and inspection certificate。

加热板表面经研磨处理，热板宽度600mm，共12块加热板，冷却定型部长4米。加热板采用容器板制作，符合国家一类压力容器标准，附有压力容器证书及检验合格证。

★Hot plate with intensive gravitational roll structure. Roll adopt pneumatic lifting.

热板采用密集型重力压辊结构。压辊采用气动升降。

★Heating plate heat transfer pipe temperature control sub-four-segment, with a temperature display.  加热板的导热配管分四段控制温度，设有温度显示。

★Double cylinder S type cotton belt tensioning device is used for upper cotton belt.

上棉织带采用双气缸S型棉织带张紧装置。

★The lower band adopts S-shape manual deflect-correcting tensioning mechanism, the structure is simple and practical, and the lower belt is a set of manual fine adjustment.

下带采用S形手动纠偏张紧机构，结构简洁实用，下带手动微调式一套。

★Drive roller coated with attached wear-resistant rubber ，showed a herringbone structure，With a high, ensure smooth cardboard output。

驱动辊表面包附耐磨像胶，呈人字型结构，并带有中高，保证纸板平整输出。

★Main drive motor for frequency conversion motor，low-speed torque，wide speed range ,reliable, and easy maintenance.

主驱动电机为变频调速电机，低速力矩大，调速范围广，使用可靠，维护简单。

★Hot plate internal for partition isolation structure,s-shaped flow of steam，Steam, water separation function significantly improves the utilization of steam。

热板内部为隔板隔离结构，使蒸汽呈S形流向，汽、水分离功能明显，提高了蒸汽利用率。

ⅱ、Technical parameter技术参数：

★Temperature requirement：160—200℃                  温度要求：160—200℃   

★Steam pressure：0.8-1.3MPa                           蒸汽压力：0.8-1.3MPa        

★Air source pressure：0.6—0.9MPa                      气源压力：0.6—0.9MPa 

★Cooling stereotypes length：4m                         冷却定型长度：4米      

★Heating plate quantity：12 pieces                       加热板数量：12块            

★Hydraulic system pressure：6---8MPa                   液压系统压力：6---8MPa 

ⅲ、Roller diameter parameter辊类直径参数：

★Upper drive rubber roller diameter：￠475mm            上驱动胶辊直径：￠475mm          

★Lower drive rubber roller diameter ：￠350mm           下驱动胶辊直径：￠350mm       

★Former follower with roller diameter：￠215mm           前从动带辊直径：￠176mm          

★Back setting belt driven roller diameter：￠176mm        后定型从动带辊直径：￠176mm

★Platen roller：￠70mm                                 压带辊直径：￠70mm           

★Setting roller diameter：￠86mm                        定型托辊直径：￠86mm

★Upper belt tension roller diameter：￠155mm             上带张紧辊直径：￠155mm         

★Upper roll diameter with detuning：￠124mm             上带调偏辊直径：￠124mm

★Entrusted with the roll diameter lower belt：￠130mm      下带托带辊直径：￠130mm

Note: All the roller surface after grinding are hard chrome plated。

注：所有辊轴表面均为磨削后镀硬铬处理。

ⅳ、Powered motor parameters动力电机参数：

★Main drive motor power：22Kw                          主驱动电机功率：22KW         

 

8、ZQS Thin knife slitting薄刀纵切压痕机  

 

ⅰ、Structural features结构特点：

★Overcome the conventional type of pole, cutting pressure lines appear when collapsed cardboard cut phenomenon, cutting board smooth, quality has improved significantly。

克服了常规的双刀型、分切压线机在裁切时出现压塌纸板的现象，切板光滑，质量明显提高。

★The whole machine can remove left and right,cycloid reducer to adjust。

整机可以左右移动，以摆线式减速机调节。

★Cutter and easy to adjust the pressure line, the error ± 0.5mm, automatic sharpening device, you can achieve timing Brothers, with intermittent Brothers and other features.

切刀和压线调整方便，误差±0.5mm，有自动磨刀装置，可以实现定时磨刀，与间隔性磨刀等多种功能。

★The machine adopt four knives six lines,the blade is made of tungsten alloy steel, the using life is not less than 3 million running meters。

本机采用4刀6压线式，刀片用钨合金钢制作，使用寿命不小于300万跑米。

ⅱ、Technical parameter技术参数：

★Effective width：1800mm                         工作幅宽：1800mm             

★Design speed: 100 m / min                        设计速度：100m/min

★Mechanical configuration: 5 knives and 8 lines       机械配置： 5刀8线               

★Minimum cutting width: 135mm                    小切纸宽度：135mm  

ⅲ、Powered motor parameters动力电机参数：

★Line cutter line motor:0.4KW                       排刀线电机:0.4KW    

★Knife wheel drive motor:5.5KW                    刀轮驱动电机:5.5KW   

 

9、NC-120  NC cutter helical knives  电脑螺旋刀横切机   

 

ⅰ、Structural features结构特点：

★It can store 200 units orders，replace the cutter specifications quickly and accurately，changing orders without stop,And enables networked computers to facilitate production management.

可储存200组定单，更换切纸规格迅速准确，不停机换单，并可实现计算机联网，方便生产管理。

★Knife shaft drive gears are precision forged steel induction hardening, backlash-free transmission, advanced keyless connection, high transmission accuracy。

刀轴传动齿轮采用精锻钢材料高频淬火，实现无侧隙传动，采用先进的无键连接方式，传动精度高。

★Cutting machine adopts inlaid front steel blade knife spiral structure, serrated knife. scissors, shears, shear force, long blade life。

横切机刀片采用镶锋钢螺旋刀结构，锯齿刀型。剪刀式剪切，剪切力小，刀片寿命长。

★Around feed rollers are used  the sun gear platen way, smooth delivery, pressure evenly, easy to crush plate board or cause blockage。

前后送纸轮均采用太阳轮压纸方式，输送平稳，压力均匀，不易压坏板板或造成堵塞。

★This type of brake is energy storage type (non-energy brake), so in the process of production, the average power consumption is 1 / 3 of that of the ordinary NC cutting machine, saving more than 70% of electricity and achieving the goal of saving money.

本机型是储能式制动（非能耗制动），故在生产过程中低能耗，平均用电量是普通NC切断机的1/3，节省电70%以上，达到省钱的目标。

★Exact and adjustable no gap gear to ensure precise blade engagement, running balance.

精密可调无隙齿轮，确保刀口精确啮合，运行平衡。

★Independent oil pump and filter are used to distribute two sets of copper pipes in each gear position to feed oil, lubricate and cool.

采用独立油泵和过滤器配合两组紫铜管分布于各齿轮位供油，润滑和冷却。

★Knife roller: fine quality forged steel material, the balanced, with good stability.

刀辊：优质精锻钢材质，经平衡处理，具有良好的平稳性。

ⅱ、Technical parameter技术参数：

★Effective width：1800mm                          工作幅宽：1800mm                  

★Operation direction：left or right（determined in accordance with customer plant）

操作方向：左置或右置（根据客户厂房确定）

★Design speed: 100 m / min                         设计速度：100m/min               

★Mechanical configuration: computer helical cutter crosscutting  机械配置：电脑螺旋刀横切

★Minimum cutting length：500mm                    小切纸长度：500mm                   

★Maximum cutting length：9999mm                  大切纸长度：9999mm

★Cutter accuracy: Uniform for ± 1mm,  non-uniform to ± 2mm

切纸精度：匀速为±1mm，非匀速为±2mm

★Equipment size: Lmx4.2 Wmx1.2 Hmx1.4            设备尺寸：L_mx4.2*W_mx1.2*H_mx1.4

★Single machine weight: maximum 3500kg            单机重量：大3500Kg

ⅲ、Roller diameter parameter辊类直径参数：

★Cross on the knife shaft center distance：￠216mm    横切上、下刀轴中心距：￠216mm        

★Before the lower conveying roller diameter  ￠156mm  前下输送辊直径  ￠156mm  

★After the lower conveying roller diameter：￠156mm   后下输送辊直径：      ￠156mm             

★Roll diameter: 160mm。                            牵纸辊直径：￠160mm          

★Output solar wheel diameter: 160mm                 输出太阳轮直径： ￠160mm

Note: all roller shafts after grinding, the surface of hard chromium plating (except upper, lower tool shaft).

注：所有辊轴均经磨削后，表面镀硬铬处（上、下刀轴除外）理。

ⅳ、Powered motor parameters动力电机参数：

★main drive motor power：12.5Kw   Full AC synchronous servo

主驱动电机功率：12.5KW             全交流同步伺服

★Before feeding motor power：3Kw（Frequency Control）

前后输纸电机功率：3KW（变频调速）

★Oil pump motor power：0.25Kw      润滑油泵电机功率：0.25KW

 

10、DMT-120paper sheet delivery and side conveyor直角堆码机 

 

ⅰ、Structural features结构特点： 

★Adopted on the 16th channel welded。Electric adjustment of cardboard the size of the lateral output pneumatic control board, electrically adjustable conveyor speed.

采用16号槽钢焊接。电动调整纸板尺寸，气动控制横向输出纸板，输送速度电动可调。

★Cardboard sheets to the desired number or height requirements will be controlled by a foot switch out of cardboard。

纸板张数或高度至所需要求时由脚踏开关控制将纸板移出。

★Vertical bin using wide flat belt conveyor transport。

纵接纸采用宽幅输送平带输送。

ⅱ、Technical parameter技术参数：

★The maximum accumulation length：3000mm  大堆积长度：3000mm                  

★The maximum stack height：200mm          大堆积高度：200mm

ⅲ、Powered motor parameters动力电机参数：

★Main conveyor motor：3Kw   adopt frequency motor

主输送电机：3KW             采用变频电机         

★Lateral output of the motor：1.5Kw    Three-phase asynchronous motor

横向输出电机：1.5KW                  三相异步电动机

★Walking Motor：1.5Kw    Three-phase asynchronous motor

行走电机：1.5KW           三相异步电动机

搜好货厂家东光县恒创利纸箱机械有限公司为您提供恒创利 瓦楞纸板生产线 单瓦生产线 瓦楞机 液压支架的详细产品价格、产品图片等产品介绍信息，您可以直接联系厂家获取恒创利 瓦楞纸板生产线 单瓦生产线 瓦楞机 液压支架的具体资料，联系时请说明是在搜好货网看到的。